Dark Silver Plum

Aus PerlenWiki
Wechseln zu: Navigation, Suche

Hier ein paar Hinweise von Amber aus dem Lampwork etc. Forum zur Verarbeitung von Dark Silver Plum:

Carla - Try annealing at a lower temp. Dark Silver Plum *is* silver glass so it can't ramp up to the normal 960 and keep color - just like Terra or others. I anneal mine around 920 and keep the purples. Laurie at LLDesigns tried this and it worked for her, too.

Also, you have to work DSP cool in the first place. If it gets too hot and goes silver, you've lost some of the metals needed to produce color.

Try this... make a rough spacer. Do not heat it up enough to completely round it out - leave ridges. Take it out of the flame, let it cool, then reheat the surface of the bead until you see a film form. You'll know when you see it. KEEP THIS FILM INTACT. Never reheat the bead to molten after this step. Just keep heating the surface, cooling, heating, cooling... the color progression goes from gold, to bronze, to magenta, to teal and then it stops. Once you see some teal, STOP! After teal, it goes silver and you've burnt off the metals. Keep practicing on small spacers and then work up to larger focals. I have found if i have to marver anything, I lose all the color progression I got.

For shards, I work the focals maybe a total of two to three minutes after they are on the bead. I heat the ends to a glow, hit the middle a little bit and straight into the kiln they go.

Original Forumsbeitrag


Carla - Versuch einmal, bei niedrigerer Temperatur zu tempern. Dunkles Pflaumenblau (DSP = Dark Silver Plum, Anm. des Übersetzers) *ist* ein Silberglas, das ich nicht auf die normale Temperatur von 516°C hochfahren kann und es behält seine Farbe - so wie Terra und andere. Ich tempere meine um 493°C und behalte die Lilatöne. Laurie von LLDesigns hat es so versucht und es hat auch bei ihr geklappt.

Du musst DSP zuerst kühl bearbeiten. Wenn es zu heiß und silbern wird verlierst Du alle Metalle, die Du später zur Farbgebung brauchst.

Versuch es so... wickle einen groben Spacer. Mach ihn nicht so heiß, dass er glatt rund wird - lass ihn unregelmäßig mit Furchen. Nimm den Spacer aus der Flamme und lass ihn abkühlen, dann die Oberfläche der Perle erwärmen bis du siehst, dass sich ein Film bildet. Du wirst es wissen, wenn du es siehst. BEWAHRE DIESEN FILM! Nach diesem Schritt darf die Perle nie mehr so heiß werden, dass sie weich wird. Mach weiter mit dem Wechsel erwärmen, abkühlen, erwärmen, abkühlen.... die Farben wechseln von Gold zu Bronze, zu Magenta, zu Blaugrün und dann hört es auf. Wenn du ein Blaugrün siehst, STOP! Nach Blaugrün wird es Silber und du hast alle Metalle verbrannt. Übe weiter mit kleinen Spacern und arbeite Dich zu großen Fokalperlen vor. Ich habe festgestellt, dass ich jegliche Farbentwicklung verliere, wenn ich die Perle irgendwie bearbeite.

Bei Shards bearbeite ich die Perle insgesamt ungefähr 2 bis 3 Minuten nachdem die Shards auf der Perle sind. Ich erhitze die Enden bis sie Glühen, streife ein wenig die Mitte und ab in den Ofen!

Barbara 09:59, 17. Okt. 2013 (CEST)